Ceiling Fan Regulator Motor Speed Control Circuit Diagram

This is a simple ceiling fan regulator circuit diagram. It is used to control the speed of a ceiling fan. In the other words it is an AC motor speed controller circuit, as because its control the speed of a AC motor(Ceiling Fan). This ceiling fan regulator circuit built with few numbers of parts. The circuit mainly based on Z0607 TRIAC. This is a low power AC semiconductor device. Generally which is used to controlling speed of low power ac motor speed.

Circuit Diagram of Ceiling Fan Regulator : 

In this ceiling fan regulator circuit, R1=500KΩ is a variable resistor that is used to adjust the fan speed. Capacitor C1 2A104J is a Polyester film capacitor. Parts List Ceiling Fan Motor Speed Controller circuit:

T1 = Z0607 -TRIAC
D1 = DB3 C312 -DIAC
R1 = 500KΩ -Variable Resistor
R2 = 37KΩ -Resistor
C1 = 2A104J -Polyester film capacitor.
M1 = Single Phase AC Motor (Ceiling Fan)-220V,50Hz

Read More

High Voltage 3 Watt Audio Power Amplifier

The LM4954 is an audio power amplifier primarily designed for demanding applications in mobile phones and other portable communication device applications. It is capable of delivering 2.4 Watts of continuous average power to an 8 BTL load with less than 1% THD+N from a 7V_DC power supply. Boomer audio power amplifiers are designed specifically to provide high quality output power with a minimal number of external components. The LM4954 does not require output coupling capacitors or bootstrap capacitors, and therefore is ideally suited for lower-power portable applications where minimal space and power consumption are primary requirements.

High Voltage 3 Watt Audio Power Amplifier Circuit Diagram

The LM4954 features a low-power consumption global shutdown mode which is achieved by driving the shutdown pin with logic low. Additionally, the LM4954 features an internal thermal shutdown protection mechanism.

The LM4954 contains advanced pop & click circuitry which eliminates noises that would otherwise occur during turn-on and turn-off transitions.

The LM4954 is unity-gain stable and can be configured by external gain-setting resistors.

Key Specification:

Wide Power Supply Voltage Range	2.7 <= VDD <= 9V
Output Power: VDD = 7V, 1% THD+N	2.4W (typ)
Quiescent power supply current	3mA (typ)
PSRR: VDD = 5V and 3V at 217Hz	80dB (typ)
Shutdown power supply current	0.01µA (typ)

Features:

No output coupling capacitors, snubber networks or bootstrap capacitors required

Unity gain stable

Externally configurable gain

Ultra low current active low shutdown mode

BTL output can drive capacitive loads up to 100pF

"Click and pop" suppression circuitry

2.7V - 9.0V operation

Available in space-saving microSMD package

Applications

Mobile Phones

PDAs

Source: http://www.ecircuitslab.com/2011/06/high-voltage-3-watt-audio-power.html

Read More

12v Battery Charger Circuit

The circuit may be accustomed charge 12V lead acid batteries.

Overview

Pin one of the LM317 IC is that the management pin that is employed to manage the charging voltage, Pin a pair of is that the output at that the charging voltage seems, Pin three is that the input to that the regulated DC offer is given.

The charging voltage and current is controlled by the electronic transistor (Q1), electrical device (R1) and POT (VR1). once the battery is 1st connected to the charging terminals, the present through R1 will increase. This successively will increase the present and voltage from LM317. once the battery is totally charged the charger reduces the charging current and also the battery are charged within the trickle charging mode.

Circuit

Notes

• The input voltage to the circuit should be a minimum of 3V more than the expected output voltage. luminous flux unit 317 dissipates around 3V throughout its operation. Here I used 18V DC because the input.
• The charging voltage may be set by victimization the POT (VR1).
• The luminous flux unit 317 should be mounted on a sink.
• All capacitors should be rated a minimum of 25V.
• Youll be able to use crocodilian clips for connecting the battery to the charger.

Read More

2W Amplifier Circuit

Designed for self-powered 8, 4 & 2 Ohm loudspeakers, Bass-boost switch

This amplifier was designed to be self-contained in a small loudspeaker box. It can be feed by Walkman, Mini-Disc, iPod and CD players, computers and similar devices fitted with line or headphone output. Of course, in most cases you will have to make two boxes to obtain stereo. The circuit was deliberately designed using no ICs and in a rather old-fashioned manner in order to obtain good harmonic distortion behavior and to avoid hard to find components. The amplifier(s) can be conveniently supplied by a 12V wall plug-in adapter.Closing SW1 a bass-boost is provided but, at the same time, volume control must be increased to compensate for power loss at higher frequencies.

Circuit diagram :

2W Amplifier Circuit Diagram

 

Parts:

P1----------10K
R1----------33K
R2----------33K
R3----------33R
R4----------15K
R5----------1K
R6----------1K
R7----------680R
R8----------120R-1/2W
R9----------100R-1/2W Trimmer Cermet
C1 ----------10µF-63V
C2 ----------10µF-63V
C3-----------100µF-25V
C4-----------470µF-25V
C5-----------47pF-63V
C7-----------470µF-25V
C6-----------220nF-63V
C8-----------1000µF-25V
D1-----------1N4148
Q1-----------BC560C
Q2-----------BC337
Q3-----------TIP31A
Q4-----------TIP32A
SW1---------SPST switch
SPKR--------3-5 Watt Loudspeaker

In use, R9 should be carefully adjusted to provide minimal audible signal cross-over distortion consistent with minimal measured quiescent current consumption; a good compromise is to set the quiescent current at about 10-15 mA.  To measure this current, wire a DC current meter temporarily in series with the collector of Q3.

Source : www.redcircuits.com

Read More