The normal working hours of the Cell Phone Jammers
Therefore, the machine work, be sure to add some water to the cooling water pump in. When the power is turned on, the pump started working equipment operational. Recycled water should be pure.
Neodymium laser emission wavelength and energy level structure of neodymium ion characteristics 4.He- Ne laser and the role of the different components of 5.We advise you to take out the battery from the Cell Phone Jammers if you don’t use it for a long time. He-Ne laser lines in the competition 3.39μm, 1.15μm, 632.8nm lines are strong, start-line resonator dielectric film by the wavelength selection mirror line decisions are strong, μ μ fixed. 3.39μm and 632.8nm on the same level, there is strong competition between the lines, and 3.39μm also has the same upper level, there is strong competition between the lines, μ μ more Strong gain coefficient in the laser is longer, in addition to the wavelength selection mirror, but also adding dispersion prism, a stronger gain coefficient.If the machine control system is not connected to power, the user must turn off the switch and control unit and data cable. b. If the data cable between the computer and the laser machine is not connected, close the master switch, connect the data cable. 4 in the process of carving and cutting overhead lines if a communication line problem, replace the communication line.Cell Phone Jammers is a burgeoning product. If the laser machine and the computer placed on the ground is not good, the user should the laser machine and the computer placed on the ground is good. What is the problem if the application software, the user should be re-placed the software and reinstall the driver software. If the laser and the ambient humidity and dust above the conflict console, cables and internal wiring, before running the machine clean and warm. If the external power supply instability and confusion, users should use a stable power supply. If the computer system error, reinstall the system or replace the computer. If the surrounding environment has a high frequency of contact, please stay away from this environment. When the carving or cutting, production can not accept the alternative or partial loss or partial file if design work beyond the width of the laser machine, the user should be designed to reduce the width and wide, so that in the appropriate range. If the document out of many, the user should be appropriate to reduce the resolving power, scanning speed or acceleration prior to the change in the absence of early scan before scanning.There are not many researches on Cell Phone Jammers originally.If the laser path deflection mirror and lens, users need to adjust the optical path.Laser pointing is the rudimental function of Cell Phone Jammers. (2) cutting / engraving depth is not enough if the laser output power is too low, the user should be increased through the control panel power output if the cutting / engraving speed is too fast, user software should be adjusted to reduce the cutting / engraving speed. If the optical path of mirrors and lenses on the overalls and dust contaminated by, or on the lens or mirror reflective layer destruction, the user should clean or replace the mirror if the focus point is not in the correct position, the user should be adjusted.
Therefore, the machine work, be sure to add some water to the cooling water pump in. When the power is turned on, the pump started working equipment operational. Recycled water should be pure.
Neodymium laser emission wavelength and energy level structure of neodymium ion characteristics 4.He- Ne laser and the role of the different components of 5.We advise you to take out the battery from the Cell Phone Jammers if you don’t use it for a long time. He-Ne laser lines in the competition 3.39μm, 1.15μm, 632.8nm lines are strong, start-line resonator dielectric film by the wavelength selection mirror line decisions are strong, μ μ fixed. 3.39μm and 632.8nm on the same level, there is strong competition between the lines, and 3.39μm also has the same upper level, there is strong competition between the lines, μ μ more Strong gain coefficient in the laser is longer, in addition to the wavelength selection mirror, but also adding dispersion prism, a stronger gain coefficient.If the machine control system is not connected to power, the user must turn off the switch and control unit and data cable. b. If the data cable between the computer and the laser machine is not connected, close the master switch, connect the data cable. 4 in the process of carving and cutting overhead lines if a communication line problem, replace the communication line.Cell Phone Jammers is a burgeoning product. If the laser machine and the computer placed on the ground is not good, the user should the laser machine and the computer placed on the ground is good. What is the problem if the application software, the user should be re-placed the software and reinstall the driver software. If the laser and the ambient humidity and dust above the conflict console, cables and internal wiring, before running the machine clean and warm. If the external power supply instability and confusion, users should use a stable power supply. If the computer system error, reinstall the system or replace the computer. If the surrounding environment has a high frequency of contact, please stay away from this environment. When the carving or cutting, production can not accept the alternative or partial loss or partial file if design work beyond the width of the laser machine, the user should be designed to reduce the width and wide, so that in the appropriate range. If the document out of many, the user should be appropriate to reduce the resolving power, scanning speed or acceleration prior to the change in the absence of early scan before scanning.There are not many researches on Cell Phone Jammers originally.If the laser path deflection mirror and lens, users need to adjust the optical path.Laser pointing is the rudimental function of Cell Phone Jammers. (2) cutting / engraving depth is not enough if the laser output power is too low, the user should be increased through the control panel power output if the cutting / engraving speed is too fast, user software should be adjusted to reduce the cutting / engraving speed. If the optical path of mirrors and lenses on the overalls and dust contaminated by, or on the lens or mirror reflective layer destruction, the user should clean or replace the mirror if the focus point is not in the correct position, the user should be adjusted.
