Low Cost Deaf People Doorbell

This circuit provides a delayed visual indication when a door bell switch is pressed. In addition, a DPDT switch can be moved from within the house which will light a lamp in the door bell switch. The lamp can illuminate the words "Please Wait" for anyone with walking difficulties.

Circuit diagram

Notes:
The circuit uses standard 2 wire doorbell cable or loudspeaker wire. In parallel with the doorbell switch, S1, is a 1N4001 diode and a 12 volt 60mA bulb.

The bulb is optional, it may be useful for anyone who is slow to answer the door, all you need to do is flick a switch inside the house, and the bulb will illuminate a label saying Please Wait inside the doorbell switch or close to it.

The double pole double throw switch sends the doorbell supply to the lamp, the 22 ohm resistor is there to reduce current flow, should the doorbell switch, S1 be pressed while the lamp is on.

The resistor needs to be rated 10 watts, the 0.5 Amp fuse protects against short circuits.

When S2 is in the up position (shown as brown contacts), this will illuminate the remote doorbell lamp. When down, (blue contacts) this is the normal position and will illuminate the lamp inside the house. Switch S1 will then charge the 47u capacitor and operate the transistor which lights the lamp.

As a door bell switch is only pressed momentarily, then the charge on the capacitor decays slowly, resulting in the lamp being left on for several seconds. If a longer period is needed then the capacitor may be increased in value.

author: Andy Collinson
e-mail: anc@mitedu.freeserve.co.uk
web site: http://www.zen22142.zen.co.uk

Read More

Digital Counter with an Interval of Kilometers

The circuit has been designed for a person who loves to jog or walk while measuring the distance that have been covered during the activity.

• 4093 – a quad 2-input NAND with Schmitt trigger inputs integrated circuit, generally characterized by small fluctuation in voltage supply, very high impedance, outputs that can sink and source, one output can drive up to 50 inputs, high speed gate propagation time, high frequency, and low power consumption.
• 4026 – a decade counter where the count advances as the clock input becomes high and has a maximum current of about 1 mA with a 4.5 V supply and 4 mA with a 9 V supply, which can light the appropriate segments of a common cathode 7-segment display.
• 4024 – a ripple counter with glitches that may occur in any logic state systems connected to its outputs due to the slight delay before the later counter outputs respond to a clock pulse; the count advances as the clock input becomes low on the falling edge as indicated by the bar over the clock label that is the usual behavior of the ripple counters which means a counter output can directly drive the clock input of the next counter in a chain.

The whole circuit may be placed in a small box and be placed in pants’ pocket where the 7-segment digital display shows the most significant digit D2 in the leftmost portion where it shows the 0 to 9 Km digits. The dot in between is always ON to segregate KM form hm. The least significant digit D1 is displayed at the rightmost part where it illustrates hundreds of meters and the dot is illuminating after every 50 meters of walking. In every two steps, a beeper will signal each count of unit, although it is not included in this circuit.

Circuit diagram :

Digital Counter with an Interval of Kilometers Circuit Diagram

A length of 78 centimeters is the calculated measure of a normal step which causes the LED to illuminate after 64 steps to signal a 50 meter distance. For a mercury switch, the illumination occurs every 32 steps. After 128 steps, the display will indicate 100 meters and so on. The SPST push button switch P2 is pressed only upon request in case of low battery consumption. Both push button switches P1 & P2 should be pressed together to reset the circuit in order to prevent accidental reset of the counters. The circuit should be considered as an approximation and not as a precision meter because it is very difficult to obtain the correct position of the mercury switch SW1 in the box where the degree of slope is being set.

The excessive bouncing of mercury switch is provided with certain degree of tolerance from the monostable multivibrator consisting of IC1A & IC1B. IC2 therefore is divided by 64 as a clean square pulse enters. The LED dot segment of D1 is driven by Q2 for every 32 pulses counted by IC2. At each monostable count, an audio frequency square is generated by IC1C for a short time. Using SW2 will disable the beep while the piezo sounder is driven by Q1. The power of beeper sound can be adjusted by trimming the value of R6. SW3 can be omitted when the display is disabled resulting to negligible current consumption.

The digital step counter circuit is widely used by people as their motion monitor while walking or jogging and other most ideal exercise possible. Some designs may come with a digital clock and backlight for easy reading during running, and belt clips.

Read More

Simple Optical Theremin Circuit Diagram

Normally, Theremin works by detecting hand proximity using capacitive coupling method. A Theremin circuit shown in the schematic diagram below use different method to control the pitch. The oscillator of this tone generator, both the volume and frequency  are controlled using LDRs, a light sensitive electronic component, so we can call this circuit an optical Theremin.  Look at the following schematic diagram.

 Simple Optical Theremin Circuit Diagram

LDR1 control the frequency of this Theremin, while LDR2 control the volume level. We can place the LDR in two boxes where we can use our hand to control the aperture of the box, allowing smooth control of light amount that expose the LDR. 

This light is expected to come from ambient light, entering the box through the hand controlled aperture. This optical Theremin assume a stable ambient light to produce smooth control. The output will be heard on a small loudspeaker, but will be in very low volume. You can just amplify this output with a standard audio power amplifier to get better loudness.

Read More

Low Cost Digital Code Lock

Many digital code lock circuits have been published in this magazine. In those circuits a set of switches (conforming to code) are pressed one by one within the specified time to open the lock. In some other circuits, custom-built ICs are used and positive and negative logic pulses are keyed in sequence as per the code by two switches to open the lock.

Digital Code Lock Circuit diagram :

A low-cost digital code lock circuit is presented in this article. Here the keying-in code is rather unique. Six switches are to be pressed to open the lock, but only two switches at a time. Thus a total of three sets of switches have to be pressed in a particular sequence. (Of these three sets, one set is repeated.) The salient features of this circuit are:

1. Use of 16 switches, which suggests that there is a microprocessor in-side.

2. Elimination of power amplifier transistor to energise the relay.

3. Low cost and small PCB size.

An essential property of this electronic code lock is that it works in monostable mode, i.e. once triggered, the output becomes high and remains so for a period of time, governed by the timing components, before returing to the quiescent low state. In this circuit, timer IC 555 with 8 pins is used. The IC is inexpensive and easily available. Its pin 2 is the triggering input pin which, when held below 1/3 of the sup-ply voltage, drives the output to high state. The threshold pin 6, when held higher than 2/3 of the supply voltage, drives the output to low state. By applying a low-going pulse to the reset pin 4, the output at pin 3 can be brought to the quiescent low level. Thus the reset pin 4 should be held high for normal operation of the IC.

Three sets of switches SA-SC, S1-S8 and S3-S4 are pressed, in that order, to open the lock. On pressing the switches SA and SC simultaneously, capacitor C3 charges through the potential divider comprising resistors R3 and R4, and on releasing these two switches, capacitor C3 starts discharging through resistor R4. Capacitor C3 and resistor R4 are so selected that it takes about five seconds to fully discharge C3.

Depressing switches S1 and S8 in unison, within five seconds of releasing the switches SA and SC, pulls pin 2 to ground and IC 555 is triggered. The capacitor C1 starts charging through resistor R1. As a result, the output (pin 3) goes high for five seconds (i.e. the charging time T of the capacitor C1 to the threshold voltage, which is calculated by the relation T=1.1 R1 x C1  seconds). Within these five seconds, switches SA and SC are to be pressed momentarily once again, followed by the depression of last code-switch pair S3-S4.

These switches connect the relay to out-put pin 3 and the relay is energised. The contacts of the relay close and the solenoid pulls in the latch (forming part of a lock) and the lock opens. The remaining switches are connected between reset pin 4 and ground. If any one of these switches is pressed, the IC is re-set and the output goes to its quiescent low state. Possibilities of pressing these reset switches are more when a code breaker tries to open the lock.

LED D5 indicates the presence of power supply while resistor R5 is a cur-rent limiting resistor.

The given circuit can be recoded easily by rearranging connections to the switches as desired by the user.

Source : www.ecircuitslab.com

Read More

Simple 4 Channel Video Amplifier using NJM2582

A very simple 4 channel video amplifier electronic circuit project can be designed using NJM2582 ic suitable for video applications with SCART connector . Design of the circuit is very simple and require few external electronic parts .

Circuit diagram :

Simple 4 Channel Video Amplifier Circuit Diagram

Some features of the NJM2582 are : Operating Voltage ±5V, +5V, +11V ; 6input 4output , 2input 1output Video SW , Internal LPF , 6dB Amplifier , Internal 75Ω Driver Circuit , DC output for SCART (FUNCTION SW, BLANKING) .

Read More

The normal working hours of the Cell Phone Jammers

The normal working hours of the Cell Phone Jammers
Therefore, the machine work, be sure to add some water to the cooling water pump in. When the power is turned on, the pump started working equipment operational. Recycled water should be pure.
Neodymium laser emission wavelength and energy level structure of neodymium ion characteristics 4.He- Ne laser and the role of the different components of 5.We advise you to take out the battery from the Cell Phone Jammers if you don’t use it for a long time. He-Ne laser lines in the competition 3.39μm, 1.15μm, 632.8nm lines are strong, start-line resonator dielectric film by the wavelength selection mirror line decisions are strong, μ μ fixed. 3.39μm and 632.8nm on the same level, there is strong competition between the lines, and 3.39μm also has the same upper level, there is strong competition between the lines, μ μ more Strong gain coefficient in the laser is longer, in addition to the wavelength selection mirror, but also adding dispersion prism, a stronger gain coefficient.If the machine control system is not connected to power, the user must turn off the switch and control unit and data cable. b. If the data cable between the computer and the laser machine is not connected, close the master switch, connect the data cable. 4 in the process of carving and cutting overhead lines if a communication line problem, replace the communication line.Cell Phone Jammers is a burgeoning product. If the laser machine and the computer placed on the ground is not good, the user should the laser machine and the computer placed on the ground is good. What is the problem if the application software, the user should be re-placed the software and reinstall the driver software. If the laser and the ambient humidity and dust above the conflict console, cables and internal wiring, before running the machine clean and warm. If the external power supply instability and confusion, users should use a stable power supply. If the computer system error, reinstall the system or replace the computer. If the surrounding environment has a high frequency of contact, please stay away from this environment. When the carving or cutting, production can not accept the alternative or partial loss or partial file if design work beyond the width of the laser machine, the user should be designed to reduce the width and wide, so that in the appropriate range. If the document out of many, the user should be appropriate to reduce the resolving power, scanning speed or acceleration prior to the change in the absence of early scan before scanning.There are not many researches on Cell Phone Jammers originally.If the laser path deflection mirror and lens, users need to adjust the optical path.Laser pointing is the rudimental function of Cell Phone Jammers. (2) cutting / engraving depth is not enough if the laser output power is too low, the user should be increased through the control panel power output if the cutting / engraving speed is too fast, user software should be adjusted to reduce the cutting / engraving speed. If the optical path of mirrors and lenses on the overalls and dust contaminated by, or on the lens or mirror reflective layer destruction, the user should clean or replace the mirror if the focus point is not in the correct position, the user should be adjusted.

Read More

Simple Strip LED Lamp

Strip LEDs are available in different colours powered by direct current (DC) source. These LEDs  are available as surface mount devices with current limiting resistors. Usually there are 300 LEDs in a 5-metre strip. The strip can be cut into pieces so that  the bits having three or four LEDs can  be used with 12V DC source. The circuit given here uses the strip LEDs to  make an automatic white LED lighting  source.

Simple Strip LED Lamp Circuit diagram:

The circuit is powered by a capacitor power supply connected to AC mains. Capacitor C1 drops the 230V  AC, which is further rectified by the bridge rectifier module and is made ripple-free by C2. Zener diode (ZD1) provides 12V DC to the comparator circuit. Resistor R1 is important in the  power supply as it provides discharge path to the voltage stored in capacitor C1 after the circuit is unplugged from  mains.

The automatic working of the circuit is based on the light-sensing property of the light-dependent resistor (LDR). Operational amplifier CA3140 (IC1) is used as a comparator with two potential dividers in its inverting and non-inverting inputs. LDR1 and  resistor R3 form one potential divider  that provides a variable voltage at the  inverting input pin 2 of IC1. Second  potential divider comprises resistors  R4 and R5, which provide half of the  supply voltage (6V) to the non-inverting pin 3 of IC1. The output of IC1 depends on voltage level at inverting  input pin 2 of IC1 as explained below.

In daylight, LDR1 has low resistance and the voltage at inverting input (pin 2) of IC1 is more than that of non-inverting input (pin 3). This makes IC1 output low, which drives transistor T1 into cut-off condition and strip LEDs do not glow. However, at night the light incident on LDR1 is low and its resistance is high. The voltage at inverting input of the comparator decreases, making it lower than the voltage at non-inverting input. This makes IC1 output high. Transistor T1 goes into saturation,  thus connecting cathodes of LEDs to  ground. All the LEDs in the strip turn  on and remain that way till morning.

Assemble the circuit on a general-purpose PCB and enclose it in a suit-able shock-proof case. Strip LEDs are available in ribbon-shaped form. Use 5cm bits (two bits) having three  LEDs each. The strip can be cut at supply-contact points. Strip LEDs are arranged on a flexible belt with  double-sided adhesive on the back  side, so it can be glued to any surface.  Connect the LED strip in the circuit  with correct polarity.

EFY note. Since the circuit uses 230V AC, there is a risk of electrical shock. Do not touch or troubleshoot when the circuit is plugged in.Before connecting the circuit to the power supply section, test it using 12V DC from a battery or DC power supply.

Source:  http://www.ecircuitslab.com/2012/05/simple-strip-led-lamp.html

Read More

Solar Powered High Efficiency Battery Charger

This is a simple NiCd battery charger powered by solar cells. A solar cell panel or an array of solar cells can charge a battery at more than 80 % efficiency provided the available voltage exceeds the ‘fully charged’ battery voltage by the drop across one diode, which is simply inserted between the solar cell array and the battery. Adding a step-down regulator enables a solar cell array to charge battery packs with various terminal voltages at optimum rates and with efficiencies approaching those of the regulator itself.

However, the IC must then operate in an unorthodox fashion (a.k.a. ‘Elektor mode’) regulating the flow of charge current in such a way that the solar array output voltage remains near the level required for peak power transfer. Here, the MAX639 regulates its input voltage instead of its output voltage as is more customary (but less interesting).

Circuit diagram:

Solar-Powered High Efficiency Charger Circuit Diagram

The input voltage is supplied by twelve amorphous solar cells with a minimum surface area of 100 cm2. Returning to the circuit, potential divider R2/R3 disables the internal regulating loop by holding the V-FB (voltage feedback) terminal low, while divider R1/R2+R3 enables LBI (low battery input) to sense a decrease in the solar array output voltage. The resulting deviation from the solar cells’ peak output power causes LBO (low battery output) to pull SHDN (shutdown) low and consequently disable the chip. LBI then senses a rising input voltage, LBO goes high and the pulsating control maintains maximum power transfer to the NiCd cells.

Current limiting inside the MAX639 creates a ‘ceiling’ of 200 mA for I out. Up to five NiCd cells may be connected in series to the charger output. When ‘on’ the regulator chip passes current from pin 6 to pin 5 through an internal switch representing a resistance of less than 1 ohm. Benefiting from the regulator’s low quiescent current (10 microamps typical) and high efficiency (85 %), the circuit can deliver four times more power than the single-diode configuration usually found in simple solar chargers. Coil L1 is a 100-µH suppressor choke rated for 600mA.

Author: D. Prabakaran - Copyright: Elektor July-August 2004

Read More

Current Limiting Coil Driver circuit Diagram

This is the Practical Current Limiting Coil Driver circuit Diagram. The p-channel devices are switched off by current sensors when the coil current reaches 10 A. The operation is similar to that of a switching-type power supply. The Schottky diodes and resistors are for spike protection.

Current Limiting Coil Driver circuit Diagram

Read More

Ceiling Fan Regulator Circuit Motor Speed Controller

This is a simple ceiling fan regulator circuit diagram tutorial. It is used to control the speed of a ceiling fan. In the other words it is an AC motor speed controller circuit, as because its control the speed of a AC motor(Ceiling Fan).  This ceiling fan regulator circuit built with few numbers of parts. The circuit mainly  based on Z0607 TRIAC. This is a low power AC semiconductor device. Generally which is used to controlling speed of low power ac motor speed. 

Circuit Diagram of Ceiling Fan Regulator :

Fig: Ceiling fan regulator (AC motor speed controller)  Circuit Diagram

In this ceiling fan regulator circuit, R1=500KΩ is a variable resistor that is used to adjust the fan speed. Capacitor C1 2A104J is a Polyester film capacitor.

Pin Diagram of  TRIAC(T1)- Z0607: 

Fig: Z0607-TRIAC Pin diagram

Pin Diagram of Variable Resistor R1:

Fig: Pin Diagram of Variable Resistor

Parts List Of Ceiling Fan-Motor Speed Controller circuit:

T1 = Z0607 -TRIAC
D1 = DB3 C312 -DIAC
R1 = 500KΩ -Variable Resistor
R2 = 37KΩ -Resistor
C1 = 2A104J -Polyester film capacitor.
M1 = Single Phase AC Motor (Ceiling Fan)-220V,50Hz

Read More

The result of the intermediate inspection of cell phone jammer

The result of the intermediate inspection of cell phone jammer should be recorded in the test report of mobile phone jammer .
Reporting its first quarter 2013 financial results today, Apple said it sold 47.8 million iPhones in the quarter, a 29 percent increase year-over-year, and up considerably from 26.9 million units

in the prior quarter. Apple sold 22.9 million iPads during the quarter, up 49 percent from the year-ago quarter and up 8.9 million units in the fourth quarter of 2012. Finally, the company said it

sold 12.7 million iPods during the quarter — an 18 percent decrease compared to the same quarter last year. Unit sales of iPhones, iPads, and iPods bring the cumulative totals for the three device

categories to 318.8 million, 120.98 million, and 369.08 million, respectively.
In what the company says was its best quarter ever for both revenues and net profits, Apple posted revenue of $54.45 billion and net quarterly profit of $13.1 billion, or $13.81 per diluted share,

compared with revenue of $46.33 billion and net quarterly profit of $13.06 billion, or $13.87 per diluted share in Q1 2012. Revenue from iTunes/Software/Services—previously known as Other Music

Related Products and Services—which includes revenue from the iTunes Store, App Store, and iBookstore, was $3.687 billion for the quarter, up 22 percent year-over-year and 5 percent from the prior

quarter. It is being separated from revenues from Apple-branded and third-party iPod accessories, which accounted for $1.829 billion in the quarter, up 25% year over year and 46% over the prior

quarter. Apple’s Board of Directors also declared a cash dividend of $2.65 per share of the Company’s common stock. The dividend is payable on February 14, 2013, to shareholders of record as of

the close of business on February 11, 2013.
“We’re thrilled with record revenue of over $54 billion and sales of over 75 million iOS devices in a single quarter,” said Tim Cook, Apple’s CEO, suggesting that the company sold at least 4.3

million iPod touches in addition to the quarter’s 70.7 million iPads and iPhones. “We’re very confident in our product pipeline as we continue to focus on innovation and making the best products

in the world.”
“We’re pleased to have generated over $23 billion in cash flow from operations during the quarter,” said Peter Oppenheimer, Apple’s CFO. “We established new all-time quarterly records for

iPhone and iPad sales, significantly broadened our ecosystem, and generated Apple’s highest quarterly revenue ever.

Read More

Mini Box 2W Amplifier with Bass Boost Switch

This amplifier was designed to be self-contained in a small loudspeaker box. It can be feed by Walkman, Mini-Disc, iPod and CD players, computers and similar devices fitted with line or headphone output. Of course, in most cases you will have to make two boxes to obtain stereo.

Mini-Box 2W Amplifier Circuit Diagram

The circuit was deliberately designed using no ICs and in a rather old-fashioned manner in order to obtain good harmonic distortion behavior and to avoid hard to find components. The amplifier(s) can be conveniently supplied by a 12V wall plug-in adapter. Closing SW1 a bass-boost is provided but, at the same time, volume control must be increased to compensate for power loss at higher frequencies.

In use, R9 should be carefully adjusted to provide minimal audible signal cross-over distortion consistent with minimal measured quiescent current consumption; a good compromise is to set the quiescent current at about 10-15 mA. To measure this current, wire a DC current meter temporarily in series with the collector of Q3.

Parts:

P1_____________10K Log.Potentiometer
R1,R2__________33K 1/4W Resistors
R3_____________33R 1/4W Resistor
R4_____________15K 1/4W Resistor
R5,R6___________1K 1/4W Resistors
R7____________680R 1/4W Resistor
R8____________120R 1/2W Resistor
R9____________100R 1/2W Trimmer Cermet
C1,C2__________10µF 63V Electrolytic Capacitors
C3____________100µF 25V Electrolytic Capacitor
C4,C7_________470µF 25V Electrolytic Capacitors
C5_____________47pF 63V Ceramic Capacitor
C6____________220nF 63V Polyester Capacitor
C8___________1000µF 25V Electrolytic Capacitor
D1___________1N4148 75V 150mA Diode
Q1____________BC560C 45V 100mA PNP Low noise High gain Transistor
Q2____________BC337 45V 800mA NPN Transistor
Q3____________TIP31A 60V 4A NPN Transistor
Q4 ___________TIP32A 60V 4A PNP Transistor
SW1___________SPST switch
SPKR__________3-5 Watt Loudspeaker, 8, 4 or 2 Ohm impedance

• Source
• Red Free Circuits

Read More

Balanced Microphone Preamplifier

The preamplifier is intended for use with dynamic (moving coil–MC) microphones with an impedance up to 200 Ω and balanced terminals. It is a fairly simple design, which may also be considered as a single stage instrument amplifier based on a Type NE5534 op amp. To achieve maximum common-mode rejection (CMR) with a balanced signal, the division ratios of the dividers (R1-R4 and R2-R5 respectively) at the inputs of the op amp must be identical. Since this may be difficult to achieve in practice, a preset potentiometer, P1, is connected in series with R5. The preset enables the common-mode rejection to be set optimally. Capacitor C1 prevents any direct voltage at the input, while resistor R7 ensures stability of the amplifier with capacitive loads.

Balanced Microphone Preamplifier Circuit diagram :

Power Supply For Balanced Microphone Preamplifier :

Resistor R3 prevents the amplifier going into oscillation when the input is open circuit. If the microphone cable is of reasonable length, R3 is not necessary, since the parasitic capacitance of the cable ensures stability of the amplifier. It should be noted, however, that R3 improves the CMR from >70 dB to >80 dB. Performance of the preamplifier is very good. The THD+N (total harmonic distortion plus noise) is smaller than 0.1% with an input signal of 1 mV and a source impedance of 50 Ω. Under the same conditions, the signal-to-noise ratio is –62.5 dBA. With component values as specified, the gain of the amplifier is 50 dB (´316). After careful adjustment of P1 at 1 kHz, the CMR, without R3, is 120 dB. The supply voltage is ±15 V. The amplifier draws a current at that voltage of about 5.5 mA. Note the decoupling of the supply lines with L1, L2, C2–C5.

Source : http://www.ecircuitslab.com/2011/06/balanced-microphone-preamplifier.html

Read More

Simple Phase Shift Meter for Audio Frequency Signal

Simple phase shift measurement can be done by squaring both the measured and the reference, then compute the difference of the two signals. The accuracy of the circuit shown in the schematic diagram  below is 1% UP to 2000 cps.

This circuit is used in computers and for high speed analog instrumentation. Negative value for zero phase shift is indicated by the zero center DC ammeter, zero for 90′ phase shift and some maximum value for 180′ phase shift.

 Phase-Shift Meter for Audio Frequency Signal Circuit Diagram

Read More

The customer asks for the classification information of Cell Phone Jammers

The customer asks for the classification information of Cell Phone Jammers .
Class 1 - uninstall the old software before installing the new version of the software the first two kinds - the new version of the software, unpack the PKG document title to the installation program consistent with the previous version. Description: Install the software is not signed 2 If the JAR process, generally because of a certificate in conflict. (a lot of java games will be out this error. solution see section 2 below.) Class 1: for software signatures. No. 2: the program (software games ) directly to your phone. The classification of Cell Phone Jammers should be performed carefully.
Description: The software license expires. Solution: the first one kind - the phone within a period of time to a certificate, and then install in the back and then installed to the correct time. The first two kinds - to re-sign software Description: cell phones period of time beyond the software license. The first one kind - check your phone date set correctly. The first two kinds - the phone within a period of time to a certificate, and then install in the back again after the installation of the correct time to. The customer needs more product catalogs of Cell Phone Jammers .
Description: 1. For the third edition of Saipan safety of the system, some of the program authority is prohibited. Without the permission of the program can not be installed. 2. Certificate error. Solution: Class 1: remove the programs banned authority (cracked cell phone). No. 2: Use the name of the software is not signed and then re-sign installation instructions: generally signed by the software or software error has been caused by multiple signatures. Solution: Use the name of the software is not signed and then re-sign installation instructions: You open the hair line to view the certificate. Solution: find a set of program management, the online certificate check to off. Note: There are several to cause this problem: 1. Handset settings issue 2 software is not signed or signed incorrectly 3 certificates conflict. To solve: 1: Go to the phone "program management" - "Options" - "Set ":" install software "----- all set" Online Certificate Check "is set to ----- off. No. 2: will not re-signed were signed before installing the software. The first three kinds: the lattice machine and then install (Note: The grid unit, please note that back up their data.) The catalog of Cell Phone Jammers includes the featured product and top-selling product. 
Voice-class business operators to provide users with voice telephone services and various value-added services like general term. Telephone service is a GSM mobile communication network to provide the most important business, through the GSM network and PSTN network, for digital mobile users and users of digital cellular mobile telephone network and fixed network users, providing real-time duplex communication, including kind of special service calls, check and declaration business operations and provide manual, automatic wireless paging services.

Read More

Simple Micro Power Supply Circuit Diagram

This is simple micro power supply circuit diagram. The circuit uses a CA3440 BiMOS op amp and CA3086 transistor array. The no-load current from 5-volt supply is 1.5 µ A. Load current can go as high as 200 µ and still maintain output voltage regulation within 0.05%.

 Micro Power Supply Circuit Diagram

Read More

Will I have to give up my favourite FM stations

Will I have to give up my favourite FM stations?
All the frequency of cell phone jammer covers the downlink power only
RM famous Real Networks Inc. to develop audio and video compression specification. RM format all known as Real Media. It contains the file format of the audio stream real audio and video streaming

file format real video file. He is a compression format developed by Real Networks Inc., a major for the online real-time transmission of video and audio information in the low rate. The smartcell

phone can install real player to reach support to play RM video, on the 7710 with the Nokia is the software bundled on the cell phone do not need our own independent installation. Some members

reflect the REAL version of our own backwardness want to upgrade but there is no way to upgrade. The manager speaks highly of the expert’s advice of cell phone jammer .
The mobile version of the real single function on a computer that can play RM format can not be used in cell phones. REAL cell phone more stringent requirements of the RM file encoding rate, which

is how some members say find a film on the cell phone but can not play, play out of a sound image, and so on. Because of this but if we want to see can be compressed to produce their own. The

conversion from film to normal play on the cell phone. WMV Windows Media Video, Microsoft defined a video format. He is out with the the realvideo competition and the development of an independent

coding in the online real-time viewing of video file compression format. Specifically with real competition, so some members often ask why our cell phones can not see this format. The cell phone

jammer system has more merits.
Hopefully, the future third-party software can allow the 7710 to implement this feature. Microsoft smartcell phone and ppc cell phones built-in Windows media player can directly watch the WMV

format, encoding quality was significantly better in realvideo, we do not say I pour cold water on me only fair to compare because it uses the mpeg4 compression algorithm, so the compression ratio

and image quality is very good. Wmv support of cell phones using Microsofts operating system is also very good, you can use the full-screen playback. Wmv all kinds of movies produced by the

corresponding software is probably around 100-200MB. After all, the famous Microsoft products, oh. The professional technician of cell phone jammer has a lot of experience in dealing with cell

phone jammer .
AVI is Audio Video Interleave, a video and audio interleaved format. Microsoft launched in 1992, the AVI technology and its applications. All AVI files include two required LIST module, any video

coding scheme can be used in AVI files. Their documents, video and audio part, these two parts in the file is stored separately.

Read More

AUTOMATIC TEMPERATURE CONTROLLED FAN

     Here is a circuit through which the speed of a fan can be linearly controlled automatically, depending on the room temperature. The circuit is highly efficient as it uses thyristors for power control. Alternatively, the same circuit can be used for automatic temperature controlled AC power control.

www.blogger.com

     In this circuit, the temperature sensor used is an NTC thermistor, i.e. one having a negative temperature coefficient. The value of thermistor resistance at 25°C is about 1 kilo-ohm.

     Op-amp A1 essentially works as I to V (current-to-voltage) converter and converts temperature variations into voltage variations. To amplify the change in voltage due to change in temperature, instrumentation amplifier formed by op-amps A2, A3 and A4 is used. Resistor R2 and zener diode D1 combination is used for generating reference voltage as we want to amplify only change in voltage due to the change in temperature.

     Op-amp μA741 (IC2) works as a comparator. One input to the comparator is the output from the instrumentation amplifier while the other input is the stepped down, rectified and suitably attenuated sample of AC voltage. This is a negative going pulsating DC voltage. It will be observed that with increase in temperature, pin 2 of IC2 goes more and more negative and hence the width of the positive going output pulses (at pin 6) increases linearly with the temperature. Thus IC2 functions as a pulse width modulator in this circuit. The output from the

comparator is coupled to an optocoupler, which in turn controls the AC power delivered to fan (load).

     The circuit has a high sensitivity and the output RMS voltage (across load) can be varied from 120V to 230V (for a temp. range of 22°C to 36°C), and hence wide variations in speed are available. Also note that speed varies linearly and not in steps. Besides, since an optocoupler is used, the control circuit is fully isolated from power circuit, thus providing added safety. Note that for any given temperature the speed of fan (i.e. voltage across load) can be adjusted to a desired value by adjusting potmeters VR1 and VR2 appropriately.

     Potmeter VR1 should he initially kept in its mid position to realise a gain of approximately 40 from the instrumentation amplifier. It may be subsequently trimmed slightly to obtain linear variation of the fan speed.

Read More

Fuse Box BMW E36 318is Diagram

Fuse Box BMW E36 318is Diagram - Here are new post for Fuse Box BMW E36 318is Diagram.

Fuse Box BMW E36 318is Diagram

Fuse Panel Layout Diagram Parts: ABS Pump relay, High speed radiator fan relay, High beam relay, Emergency flasher relay, A/C Blower relay, Rear defogger relay, ABS System relay, A/C Compressor relay Low Speed Radiator fan relay, Fuel pump relay, Sysem relay, Oxygen Sensor Heater relay, Horn relay, Taillight/Foglight relay, Low beam relay.

Read More

2008 Ford F 350 DIESEL Wiring Diagram

2008 Ford F-350 DIESEL Wiring Diagram

The Part of 2008 Ford F-350 DIESEL Wiring Diagram: battery junction, engine compartment, fusible
link,power distribution system, starter relay center, assembly, red wire, black wire, compartment fender, engine compart, lamp switch, starter motor, ref volt, torq shift transmission, central junction box

Read More